We apologise for any inconvenience our phones are currently down please send emails to info@shoprvparts.com.au in the interim
Contact Us: info@shoprvparts.com.au
We apologise for any inconvenience our phones are currently down please send emails to info@shoprvparts.com.au in the interim
Contact Us: info@shoprvparts.com.au
Upgrade your vehicle's capabilities with our range of external fittings, including oil seals, shields, and brackets. Enhance performance and protection with fittings that meet the demands of both rugged adventures and daily commutes. Perfect for a wide range of cars, caravans and RVs, this range includes winch kits, bike racks, bearings and more. Explore the selection below and find what you need to take your vehicle to the next level.
This U bolt kits contain the U bolts, nuts and washers for fixing one axle.
When ordering for a multi axle application, order the number of kits to correspond with the number of axles.
Includes:
2 x U-Bolts
4 x Nyloc Nuts
4 x Washers
All of AL-KO's hubs are manufactured from high grade ductile iron to give maximum achievable strength
Some of AL-KO's hubs are available in zinc plated or hot dipped galvanised finish as well as the traditional raw cast finish
The capacity of a hub is dependent on the size of wheel bearings fitted and such dimensional limits such as flange diameter and the available hole in the wheel to which it is fitted (on the hub this is the hub outer boss dimension)
To ascertain what hub from the vast AL-KO range is required it is important to know the following:
Total load you expect a pair of hubs to carry in kg.
Wheel bearing type to be fitted (LM, slimline, 1.5 t, etc)
Wheel drilling pattern (4 stud Datsun, 5 stud Mini, 5 Stud HQ Holden, 5 stud Ford, 6 stud Landcruiser)
Includes:
1 x 6” Hub fitted with 5 x 7/16” UNF wheel studs
4 x 7/16” UNF wheel nuts
1 x Bearing Cone LM67048 - Chinese
1 x Bearing Cone LM11949 - Chinese
1 x Seal - LM Type
1 x Grease cap
U Bolt fish are required to connect your axle to your springs. The U Bolt fish plate sits on the threaded side of the U bolt and is fastened to the U Bolt using a washer and nut.
This U Bolt fish plate is slotted to allow for U bolts with a width of 39mm to 56mm.
Hole centre to centre perpendicular to slot is 45mm.
All of AL-KO's hubs are manufactured from high grade ductile iron to give maximum achievable strength.
Some of AL-KO's hubs are available in zinc plated or hot dipped galvanised finish as well as the traditional raw cast finish.
The capacity of a hub is dependent on the size of wheel bearings fitted and such dimensional limits such as flange diameter and the available hole in the wheel to which it is fitted (on the hub this is the hub outer boss dimension).
To ascertain what hub from the vast AL-KO range is required it is important to know the following:
Total load you expect a pair of hubs to carry in kg.
Wheel bearing type to be fitted (LM, slimline, 1.5 t, etc).
Wheel drilling pattern (4 stud Datsun, 5 stud Mini, 5 Stud HQ Holden, 5 stud Ford, 6 stud Landcruiser).
Includes:
1 x 6” Hub fitted with 5 x 1/2” wheel studs.
5 x 1/2” UNF wheel nuts
1 x Bearing Cone LM68149 - Chinese
1 x Bearing Cone LM12749 - Chinese
1 x Seal - SL Type
1 x Grease cap
All of AL-KO's hubs are manufactured from high grade ductile iron to give maximum achievable strength.
Some of AL-KO's hubs are available in zinc plated or hot dipped galvanised finish as well as the traditional raw cast finish.
The capacity of a hub is dependent on the size of wheel bearings fitted and such dimensional limits such as flange diameter and the available hole in the wheel to which it is fitted (on the hub this is the hub outer boss dimension).
To ascertain what hub from the vast AL-KO range is required it is important to know the following:
Total load you expect a pair of hubs to carry in kg.
Wheel bearing type to be fitted (LM, slimline, 1.5 t, etc).
Wheel drilling pattern (4 stud Datsun, 5 stud Mini, 5 Stud HQ Holden, 5 stud Ford, 6 stud Landcruiser).
Includes:
1 x Galvanised hub fitted with 5 x zinc plated 7/16” wheel studs.
5 x zinc plated 7/16” UNF wheel nuts
1 x Bearing Cone LM68149 - Chinese
1 x Bearing Cone LM12749 - Chinese
1 x 2 Piece Marine Seal - SL Type
1 x Grease cap
Secure your caravan, boat trailer, box trailer or horse float against theft using this simple wheel clamp.
The AL-KO wheel clamp is made out of heavy duty steel and is powder coated for weather resistance.
A weather cover is attached to the locks to minimise water ingress whilst in use.
The contact ends of the wheel clamp have an anti-scratch coating to protect your wheels. Includes two keys.
Trailer wheel bearings comprise of two parts, the cup which is pressed into the hub and the cone. This is the part that contains the rollers of the caravan wheel bearing. Caravan and Trailer wheel bearings should always be replaced in a set, that is the cup and cone together.
In a bearing combination in a hub, the bearing on the inside of the hub flange (the side closest to the centre of the trailer is called the inner bearing.
The bearing on the outside is called the outer bearing.
LM (Holden bearings) are rated for 750 kg on a 39 mm round or 40 mm square axle.
LM Trailer Bearing Kit Includes:
1 x Cinese bearing cup LM67010
1 x Chinese bearing cone LM67048
1 x Chinese bearing cup LM11910
1 x Chinese bearing cone LM11949
1 x Grease cup H26
1 x Seal 609 - LM Type
1 x Split pin 4MM x 25MM Zinc
All of AL-KO's hubs are manufactured from high grade ductile iron to give maximum achievable strength.
Some of AL-KO's hubs are available in zinc plated or hot dipped galvanised finish as well as the traditional raw cast finish.
The capacity of a hub is dependent on the size of wheel bearings fitted and such dimensional limits such as flange diameter and the available hole in the wheel to which it is fitted (on the hub this is the hub outer boss dimension).
To ascertain what hub from the vast AL-KO range is required it is important to know the following:
Total load you expect a pair of hubs to carry in kg.
Wheel bearing type to be fitted (LM, slimline, 1.5 t, etc).
Wheel drilling pattern (4 stud Datsun, 5 stud Mini, 5 Stud HQ Holden, 5 stud Ford, 6 stud Landcruiser).
Includes:
1 x Galvanised Disc Hub fitted with 5x 7/16” UNF wheel studs.
5x 7/16” UNF wheel nuts
1 x Bearing Cone LM67048 - Chinese
1 x Bearing Cone LM11949 - Chinese
1 x Marine Seal - LM Type
1 x Grease cap
Includes:
1 x Galvanised Disc Hub fitted with 5 x 1/2” wheel studs.
5 x 1/2” UNF wheel nuts
1 x Bearing Cone LM67048 - Chinese
1 x Bearing Cone LM11949 - Chinese
1 x Marine Seal - LM Type
1 x Grease cap
Trailer wheel bearings comprise of two parts, the cup which is pressed into the hub and the cone. This is the part that contains the rollers of the caravan wheel bearing. Caravan and Trailer wheel bearings should always be replaced in a set, that is the cup and cone together.
In a bearing combination in a hub, the bearing on the inside of the hub flange (the side closest to the centre of the trailer is called the inner bearing.
The bearing on the outside is called the outer bearing.
SL (Slimline or Ford) bearings are rated for 1500 kg on a 45 mm round or square axle.
Slimline Trailer Bearing Kit Includes:
1 x Chinese bearing cup L68110
1 x Chinese bearing cone L68149
1 x Chinese bearing cup LM12710
1 x Chinese bearing cone LM12749
1 x Grease cap H26
1 x Seal - 28600 - Slimline type
1 x Split pin 4MM x 25MM Zinc
Compatible with Milenco's NEW superior level system which has been designed to make levelling easier for you.
This level has been manufactured using a truly versatile system complete with Tyre Saver Top. Simply stack the pieces together placing the Tyre Saver on the top to construct the desired height. Compatible with the Superlevel for easy levelling.
Solid base to prevent sinking on soft ground or sand. High quality heavy duty durable design.
Suitable for Caravans, Motorhomes, Twin Axle, Single Axle and Tag Axle.
MGI Milenco Levels are high quality products. Lightweight strong construction, high grip non slip surface. High grip leading edge, so no need to use gripper plates. Extra wide chock comes with side handle to reduce risk of hand trap.
Milenco Chocks are a high-quality product.
Lightweight strong construction, high grip non-slip surface.
Designed to be used with Milenco - Wedge Level - Vehicle Levelling - Pair - MIL5227
Extra-wide chock comes with a side handle to reduce risk of hand trap.
A Conventional Wedge-shaped Level with 50% Base and 50% Top Surface area.
MGI Milenco Levels are high-quality products. Lightweight strong construction, high grip non-slip surface.
High grip leading edge, so no need to use gripper plates
This U bolt kits contain the U bolts, nuts and washers for fixing one axle.
When ordering for a multi axle application, order the number of kits to correspond with the number of axles.
Includes:
2 x U-Bolts
4 x Nyloc Nuts
4 x Washers
All of AL-KO's hubs are manufactured from high grade ductile iron to give maximum achievable strength
Some of AL-KO's hubs are available in zinc plated or hot dipped galvanised finish as well as the traditional raw cast finish
The capacity of a hub is dependent on the size of wheel bearings fitted and such dimensional limits such as flange diameter and the available hole in the wheel to which it is fitted (on the hub this is the hub outer boss dimension)
To ascertain what hub from the vast AL-KO range is required it is important to know the following:
Total load you expect a pair of hubs to carry in kg.
Wheel bearing type to be fitted (LM, slimline, 1.5 t, etc)
Wheel drilling pattern (4 stud Datsun, 5 stud Mini, 5 Stud HQ Holden, 5 stud Ford, 6 stud Landcruiser)
Includes:
1 x 6” Hub fitted with 5 x 7/16” UNF wheel studs
4 x 7/16” UNF wheel nuts
1 x Bearing Cone LM67048 - Chinese
1 x Bearing Cone LM11949 - Chinese
1 x Seal - LM Type
1 x Grease cap
U Bolt fish are required to connect your axle to your springs. The U Bolt fish plate sits on the threaded side of the U bolt and is fastened to the U Bolt using a washer and nut.
This U Bolt fish plate is slotted to allow for U bolts with a width of 39mm to 56mm.
Hole centre to centre perpendicular to slot is 45mm.
All of AL-KO's hubs are manufactured from high grade ductile iron to give maximum achievable strength.
Some of AL-KO's hubs are available in zinc plated or hot dipped galvanised finish as well as the traditional raw cast finish.
The capacity of a hub is dependent on the size of wheel bearings fitted and such dimensional limits such as flange diameter and the available hole in the wheel to which it is fitted (on the hub this is the hub outer boss dimension).
To ascertain what hub from the vast AL-KO range is required it is important to know the following:
Total load you expect a pair of hubs to carry in kg.
Wheel bearing type to be fitted (LM, slimline, 1.5 t, etc).
Wheel drilling pattern (4 stud Datsun, 5 stud Mini, 5 Stud HQ Holden, 5 stud Ford, 6 stud Landcruiser).
Includes:
1 x 6” Hub fitted with 5 x 1/2” wheel studs.
5 x 1/2” UNF wheel nuts
1 x Bearing Cone LM68149 - Chinese
1 x Bearing Cone LM12749 - Chinese
1 x Seal - SL Type
1 x Grease cap
All of AL-KO's hubs are manufactured from high grade ductile iron to give maximum achievable strength.
Some of AL-KO's hubs are available in zinc plated or hot dipped galvanised finish as well as the traditional raw cast finish.
The capacity of a hub is dependent on the size of wheel bearings fitted and such dimensional limits such as flange diameter and the available hole in the wheel to which it is fitted (on the hub this is the hub outer boss dimension).
To ascertain what hub from the vast AL-KO range is required it is important to know the following:
Total load you expect a pair of hubs to carry in kg.
Wheel bearing type to be fitted (LM, slimline, 1.5 t, etc).
Wheel drilling pattern (4 stud Datsun, 5 stud Mini, 5 Stud HQ Holden, 5 stud Ford, 6 stud Landcruiser).
Includes:
1 x Galvanised hub fitted with 5 x zinc plated 7/16” wheel studs.
5 x zinc plated 7/16” UNF wheel nuts
1 x Bearing Cone LM68149 - Chinese
1 x Bearing Cone LM12749 - Chinese
1 x 2 Piece Marine Seal - SL Type
1 x Grease cap
Secure your caravan, boat trailer, box trailer or horse float against theft using this simple wheel clamp.
The AL-KO wheel clamp is made out of heavy duty steel and is powder coated for weather resistance.
A weather cover is attached to the locks to minimise water ingress whilst in use.
The contact ends of the wheel clamp have an anti-scratch coating to protect your wheels. Includes two keys.
Trailer wheel bearings comprise of two parts, the cup which is pressed into the hub and the cone. This is the part that contains the rollers of the caravan wheel bearing. Caravan and Trailer wheel bearings should always be replaced in a set, that is the cup and cone together.
In a bearing combination in a hub, the bearing on the inside of the hub flange (the side closest to the centre of the trailer is called the inner bearing.
The bearing on the outside is called the outer bearing.
LM (Holden bearings) are rated for 750 kg on a 39 mm round or 40 mm square axle.
LM Trailer Bearing Kit Includes:
1 x Cinese bearing cup LM67010
1 x Chinese bearing cone LM67048
1 x Chinese bearing cup LM11910
1 x Chinese bearing cone LM11949
1 x Grease cup H26
1 x Seal 609 - LM Type
1 x Split pin 4MM x 25MM Zinc
All of AL-KO's hubs are manufactured from high grade ductile iron to give maximum achievable strength.
Some of AL-KO's hubs are available in zinc plated or hot dipped galvanised finish as well as the traditional raw cast finish.
The capacity of a hub is dependent on the size of wheel bearings fitted and such dimensional limits such as flange diameter and the available hole in the wheel to which it is fitted (on the hub this is the hub outer boss dimension).
To ascertain what hub from the vast AL-KO range is required it is important to know the following:
Total load you expect a pair of hubs to carry in kg.
Wheel bearing type to be fitted (LM, slimline, 1.5 t, etc).
Wheel drilling pattern (4 stud Datsun, 5 stud Mini, 5 Stud HQ Holden, 5 stud Ford, 6 stud Landcruiser).
Includes:
1 x Galvanised Disc Hub fitted with 5x 7/16” UNF wheel studs.
5x 7/16” UNF wheel nuts
1 x Bearing Cone LM67048 - Chinese
1 x Bearing Cone LM11949 - Chinese
1 x Marine Seal - LM Type
1 x Grease cap
Includes:
1 x Galvanised Disc Hub fitted with 5 x 1/2” wheel studs.
5 x 1/2” UNF wheel nuts
1 x Bearing Cone LM67048 - Chinese
1 x Bearing Cone LM11949 - Chinese
1 x Marine Seal - LM Type
1 x Grease cap
Trailer wheel bearings comprise of two parts, the cup which is pressed into the hub and the cone. This is the part that contains the rollers of the caravan wheel bearing. Caravan and Trailer wheel bearings should always be replaced in a set, that is the cup and cone together.
In a bearing combination in a hub, the bearing on the inside of the hub flange (the side closest to the centre of the trailer is called the inner bearing.
The bearing on the outside is called the outer bearing.
SL (Slimline or Ford) bearings are rated for 1500 kg on a 45 mm round or square axle.
Slimline Trailer Bearing Kit Includes:
1 x Chinese bearing cup L68110
1 x Chinese bearing cone L68149
1 x Chinese bearing cup LM12710
1 x Chinese bearing cone LM12749
1 x Grease cap H26
1 x Seal - 28600 - Slimline type
1 x Split pin 4MM x 25MM Zinc
Compatible with Milenco's NEW superior level system which has been designed to make levelling easier for you.
This level has been manufactured using a truly versatile system complete with Tyre Saver Top. Simply stack the pieces together placing the Tyre Saver on the top to construct the desired height. Compatible with the Superlevel for easy levelling.
Solid base to prevent sinking on soft ground or sand. High quality heavy duty durable design.
Suitable for Caravans, Motorhomes, Twin Axle, Single Axle and Tag Axle.
MGI Milenco Levels are high quality products. Lightweight strong construction, high grip non slip surface. High grip leading edge, so no need to use gripper plates. Extra wide chock comes with side handle to reduce risk of hand trap.
Milenco Chocks are a high-quality product.
Lightweight strong construction, high grip non-slip surface.
Designed to be used with Milenco - Wedge Level - Vehicle Levelling - Pair - MIL5227
Extra-wide chock comes with a side handle to reduce risk of hand trap.
A Conventional Wedge-shaped Level with 50% Base and 50% Top Surface area.
MGI Milenco Levels are high-quality products. Lightweight strong construction, high grip non-slip surface.
High grip leading edge, so no need to use gripper plates
© 2022 Shop RV Parts Australia. All Rights Reserved
